K-Seal FAQs
If you have a question about our products or services that we haven’t covered elsewhere on the site, you can find the answer here.
For K‑Seal to work effectively it needs to be exposed to an atmosphere. This can be externally or internally (across the head to the cylinders). Where coolant is leaking into the oil it is less likely that K‑Seal will be exposed to an atmosphere. Therefore, there is a reduced chance of K‑Seal making a successful repair.
No. K‑Seal will only fix coolant leaks and cannot stop oil leaks.
No. K‑Seal can only fix leaks in ‘solid’ parts of the cooling system including the head, head gasket, block, core plug, radiator and heater core.
What you are seeing is not smoke but steam condensing as it exits the exhaust and hits cold air (just like when a kettle boils). The steam is the result of water entering the cylinder(s) due to a head gasket failure. The water boils in the cylinder and is expelled with the exhaust gases. You may also notice reduced engine performance, starting problems and fouled spark plugs.
One cause of misting windshields is when there is a leak in the heater core. The heater core transfers heat from the coolant into warm air to heat up the cabin. If there is a coolant leak in the core, then this contaminates the air entering the cabin. The moisture then condenses on the windshield cause the misting. You may also detect the smell of coolant/antifreeze and, in extreme cases, you will notice damp patches in the footwells.
This indicates that you have water (coolant) leaking into the oil due to a head gasket problem. The water and oil combine and emulsify (a bit like mayonnaise) which results in the deposits around the filler cap.
K‑Seal can fix this type of leak but you need to get K‑Seal into the cooling system without it first being blown out by the gases blowing back from the cylinders. A couple of solutions are:
Even though there is pressure coming into the cooling system, there is almost always a small movement of coolant back across the crack as the pistons move up and down within the cylinder. K‑Seal is drawn into the crack and is then cured as the hot gases pass back through the crack.
Additional installation tips and information
Unlike other block sealers, K‑Seal is a simple ‘pour & go’ solution. Shake the bottle well and then add the entire contents to the cooling system where you would normally top up the coolant/water.
1 standard bottle of K‑Seal (236ml/8floz) will treat cooling systems with a capacity up to 20 liters (this covers motorcycles up to light commercial vehicles). For larger cooling systems use our Heavy Duty (472ml/16floz) size K‑Seal.
K‑Seal can be added to a cold or a hot engine. The important thing is that, once K‑Seal is in the coolant, you run the engine up to operating temperature to make sure that the coolant/K‑Seal is flowing freely around the system.
K‑Seal must only be added to the coolant. Do not add K‑Seal to the oil.
It is not necessary to leave K‑Seal in the cooling system after the leak has been repaired although it will do no harm if you do so. Once K‑Seal makes a repair then that repair is permanent, regardless of whether you leave it in the system or not.
When K‑Seal repairs a leak then that repair is permanent.
Unfortunately, there are some problems that are beyond even K‑Seal’s ability to seal leaks. In the unlikely event this should be the case please get in touch with us and we can investigate why this did not work.
K‑Seal repairs a head gasket leak by filling the crack with ceramic microfibers that cure to make a permanent repair. If you decide to replace the head gasket at a later date the K‑Seal repair will be removed with the old gasket.
K‑Seal is suitable for use with all water cooled engines, regardless of size or fuel type.
There is no major difference between coolant and antifreeze as they are just different names for the same additive. Cooling systems now contain additives which not only prevent the water in the system from freezing but also help the cooling process in hot weather.
Yes. K‑Seal is compatible with DEX-COOL and all other types and brands of antifreeze/coolant. Unlike many other products, there is no need to drain or flush the cooling system before adding K‑Seal. Just shake, pour and go!
Yes. K‑Seal is compatible with Evans so long as the dosage of does not exceed 5% water within the cooling system. In a family size vehicle even the 16oz / 472ml size K-Seal should not exceed this maximum.
Yes. K‑Seal does not react with coolant or other additives that may already be present in the system.
A water based heating system is very similar to an automotive cooling system, so K-Seal can be used in a hot water central heating system. In both systems you have a hot liquid flowing around a closed loop with the intention of transferring heat from the system to the surrounding environment through radiation. If there is a leak in the system this compromises the efficiency for the system and can lead to long term damage.
Adding K‑Seal to the central heating system can help repair leaks up to 0.6mm in size without the need to drain the system. Simply add K‑Seal to the heating system where you would normally top up the water. If the system is fitted with a filter, then this should be bypassed before adding K‑Seal. K‑Seal meets ASTM D-3147.
No. Scientifically tested, K‑Seal will not cause any harm to your car or its engine, nor will it damage the pump. It simply does what it says on the bottle: seals holes in your coolant system and cracks in your head gasket with ease, without the risk of blockages.
K‑Seal will not block the cooling system and is safe to use with all types of water cooled engine.
Yes. K‑Seal is suitable for use with aluminum and all other radiator materials. It will even repair leaks in hard plastic radiator casings.
It is possible to add K‑Seal to the cooling system even if there is no leak. However, the effectiveness of K‑Seal reduces over time and, due to the varying conditions in different cooling systems, it is not possible to determine exactly how long K‑Seal will remain effective.